@could.be.printedbyprusa · Could be printedbyprusa
Saved 2026-05-15 · Posted 2025-01-22 · Status: New
The best 3D printing supports! . Video by @cswilsonprints (Definitely check that out) . Do you have anything interesting to share? Feel free to reach out!
Comments
(14)
@felixvolz18♥ 22025-05-03
Is there any Filament which does the same with ABS? I heard Hips should work but there are no Videos out there
@steampunk_balis♥ 22025-02-03
How do you keep the petg print from snapping off at the interface layer of the pla? That was my issue
@healthandfitnesskd♥ 12025-01-25
This is cool can it be done on any printer
@jp_peguer2025-07-14
I i dont have ams😢, how can i do it???
@rob.estes2025-06-08
What do you use for flushing volumes? I run into issues where it isn’t flushing enough, so I end up with layer issues in the model.
@nomadrekkrairsoft_2025-04-04
One thing you forgot to mention. Build plate temps. When using PLA as support interface and using Engineer plate you have set the PLA (cool plate) temps the same. Or it won’t slice.
@bartboma2025-02-18
The x1 can do 8 colors and petg?
@matteo.m4052025-02-08
Had Problems, that the Layer where is the material Switch to Pla for Support is very easy to break the petg model
@3d_fantacyforge2025-02-05
@could.be.printedbyprusa I love how easy this method is to remove supports using this method but it seems to make the next few layers after the supports extremely weak. Have you noticed this? I’m wondering if the purge time and prime tower need to be longer/bigger.
@eugen.schmidt.1462025-01-30
Das ist absolut Suboptimal. Die Druckzeit erhöht sich. Das " Poop" wird dadurch auch viel mehr.
@tiasimo2025-01-28
The problem is that if you do not clean your nozzle with a LOT of flushing volume, your part becomes very week, as it contaminated the other material and your later adhesion becomes weak
@rufid29392025-01-27
Do you print with PVA?
@zach_low_2025-01-26
How about for tree supports
@sightsincolor2025-01-24
Is it worth it though with the time it adds?
Content ideas (0)
No ideas generated yet. Run /instagram-sync ideate from Claude Code to create some.
Comments (14)
Is there any Filament which does the same with ABS? I heard Hips should work but there are no Videos out there
How do you keep the petg print from snapping off at the interface layer of the pla? That was my issue
This is cool can it be done on any printer
I i dont have ams😢, how can i do it???
What do you use for flushing volumes? I run into issues where it isn’t flushing enough, so I end up with layer issues in the model.
One thing you forgot to mention. Build plate temps. When using PLA as support interface and using Engineer plate you have set the PLA (cool plate) temps the same. Or it won’t slice.
The x1 can do 8 colors and petg?
Had Problems, that the Layer where is the material Switch to Pla for Support is very easy to break the petg model
@could.be.printedbyprusa I love how easy this method is to remove supports using this method but it seems to make the next few layers after the supports extremely weak. Have you noticed this? I’m wondering if the purge time and prime tower need to be longer/bigger.
Das ist absolut Suboptimal. Die Druckzeit erhöht sich. Das " Poop" wird dadurch auch viel mehr.
The problem is that if you do not clean your nozzle with a LOT of flushing volume, your part becomes very week, as it contaminated the other material and your later adhesion becomes weak
Do you print with PVA?
How about for tree supports
Is it worth it though with the time it adds?