Saved 2026-07-02 · Posted 2026-06-27 · Status: New
#diy Last Minute present by electroplating #3Dprint with Copper and Gold. John wick gold coin.
Comments
(14)
@hen3drik♥ 252026-06-26
It is a DIY 4 micron graphite + acetone + glue mixture
@hen3drik♥ 72026-06-26
Ask me anything here.
@emrhmrs♥ 42026-06-26
What is the liquid you applied in the first step? Do you have a video that explains the entire process in detail?
@brianvdberg♥ 22026-06-27
Is this something one can do in their own space like a garage or would that be dangerous?
@4emperors_design♥ 12026-06-27
Saucool wie immer 😍 Was hälst du von den Leitlacken die es bereits angemischt in der Spraydose gibt? Jetzt nicht die Billo Dinger, sondern die anscheinend Guten für 50-60€
@grantbrad07♥ 12026-06-26
Does it still feel around the same weight the 3d print was beforehand
@misza.962026-06-27
Hello Hen3drik! Could you elaborate on other chemical solutions? Like instead of acid electrolyte could be alkaline elecyrolyte?
@nickybroadowens2026-06-27
Does the wire holding the coin ever cover a spot on the electroplating?
@the_mad_maker_12272026-06-27
how long to you let the conductive paint dry prior to buffing and dipping into the bath.
@pin_fandango2026-06-27
Can lasting jewelry be made using this process or does it break down with repeated use, wear, etc?
@pin_fandango2026-06-27
How hard to bend are these once they are covered in metal like that? Does the metal rub off with use?
@roberto_quaranta_2026-06-27
Really very interesting, especially the graphite solution you made. For my work I use a very fine copper powder but I'm interested in your idea. What kind of glue do you use for the solution. Anyway I'm really fascinated
@its_all_poppin_off2026-06-27
If we can’t make our own can we buy something like this? The glue stuff..
@thealfredsource2026-06-27
Where or how did did you make solution for nickel?
Content ideas (0)
No ideas generated yet. Run /instagram-sync ideate from Claude Code to create some.
Comments (14)
It is a DIY 4 micron graphite + acetone + glue mixture
Ask me anything here.
What is the liquid you applied in the first step? Do you have a video that explains the entire process in detail?
Is this something one can do in their own space like a garage or would that be dangerous?
Saucool wie immer 😍 Was hälst du von den Leitlacken die es bereits angemischt in der Spraydose gibt? Jetzt nicht die Billo Dinger, sondern die anscheinend Guten für 50-60€
Does it still feel around the same weight the 3d print was beforehand
Hello Hen3drik! Could you elaborate on other chemical solutions? Like instead of acid electrolyte could be alkaline elecyrolyte?
Does the wire holding the coin ever cover a spot on the electroplating?
how long to you let the conductive paint dry prior to buffing and dipping into the bath.
Can lasting jewelry be made using this process or does it break down with repeated use, wear, etc?
How hard to bend are these once they are covered in metal like that? Does the metal rub off with use?
Really very interesting, especially the graphite solution you made. For my work I use a very fine copper powder but I'm interested in your idea. What kind of glue do you use for the solution. Anyway I'm really fascinated
If we can’t make our own can we buy something like this? The glue stuff..
Where or how did did you make solution for nickel?